Makita 5" Sjsii High-power Angle Grinder Instruction Manual – Page 2

Posted on 11 Jun, 2019
Manufacturer: Makita
Category: Angle Grinders
Product: Makita 5" Sjsii High-power Angle Grinder
Model Number: GA5042C
Pages: 48
File size: 2 MB

2
ENGLISH (Original instructions)
SPECIFICATIONS
Model
GA4542C GA4543C GA5042C GA5043C GA6042C
Wheel diameter
115 mm (4-1/2")
125 mm (5")
150 mm (6")
Spindle thread
5/8"
5/8"
5/8"
No load speed (RPM)
2,800 - 11,000 /min
2,800 - 11,000 /min
4,000 - 9,000 /min
Overall length
303 mm
(11-7/8")
325 mm
(12-3/4")
303 mm
(11-7/8")
325 mm
(12-3/4")
303 mm
(11-7/8")
Net weight
2.5 kg
(5.4 lbs)
2.7 kg
(5.9 lbs)
2.5 kg
(5.4 lbs)
2.7 kg
(5.9 lbs)
2.6 kg
(5.8 lbs)
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
GEA008-2
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in
electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit.
Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids
, gases or dust.
Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool.
Distractions can cause
you to lose control.
Electrical Safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of
electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions.
Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord.
Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply.
Use of an
GFCI reduces the risk of electric shock.
Personal Safety
10.
Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication.
A moment of inattention while
operating power tools may result in serious
personal injury.
11.
Use personal protective equipment. Always
wear eye protection.
Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12.
Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. .
Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
13.
Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left
attached to a rotating part
of the power tool may
result in personal injury.